Virpul household appliances are known for their quality and manufacturability, even the electronic control of the dishwasher is equipped with a self-diagnosis system. With its help, the technician notifies the user of a malfunction. Whirlpool dishwasher errors are displayed as a code.
To find out the meaning of the code and begin to search for damage, read our article.
A fault code indicates a specific malfunction in the control system. To start its search, disconnect the PMM from the network, turn off the water supply. If you do not know how to restart the machine, do this:
If the dishwasher has recovered after a reboot, it means that there was a system failure. But if the malfunction is highlighted again, then you need to look for its cause.
(E - blinks, F - flashes)
1. Inspect the dishwasher tank for leaks.
2. Check the connections and tightness of the inlet and drain hose. If a leak is detected, tighten the connections or replace the element.
Why water is not heated in the PMM:
1. The heating element is broken.
2. The thermostat has broken.
3. Heater connections are broken.
4. Problems with the control module.
How to fix the situation:
1. Check the heater for serviceability. Disconnect its wiring and measure the resistance at the contacts with a multimeter. If broken, install a new heater.
2. Check and replace the thermostat.
3. Inspect the contacts at the time of burnout. Repair if necessary.
4. If you notice problems with the control module, it is better to contact a service center.
1. The water is off.
2. The inlet tap is shut off.
3. Insufficient pressure in the system.
4. Blockage in the filler system (intake hose, filter, inlet valve).
5. Failure of the intake valve.
What can be done:
1. Open the tap, check for water.
2. Turn the shut-off valve.
3. Wait until normal pressure resumes.
4. Inspect and clean the inlet hose. Clean the filter screen, which is located on the body behind the hose.
5. Diagnose the intake valve. Install a new part.
1. Blockage in the drain path: filter, hose, pump.
2. Problems with the operation of the drain or circulation pump.
1. Check and clean the filter at the bottom of the dishwasher hopper, drain pump and hose.
2. Inspect the circulation pump. Replace if broken.
1. Problems with the float sensor.
2. Depressurization of the tank, connections, hoses.
1. Diagnostics of the Aquastop system. Replacement in case of failure.
2. Inspection of the tank and other PMM systems. Leak detection and repair.
1. The heater has broken.
2. The relay on the control module, which is responsible for the operation of the heater, has burned.
3. Damage to the thermistor.
DIY repair:
1. Diagnosis and installation of a new heater in the dishwasher.
2. Inspection of the control board. Repair and replacement of relays.
3. Check the thermistor.
1. The drain pump is broken or blocked.
2. Clogged drain hose or sewer.
3. Problems with the electronic module.
How to fix the situation:
1. Clean the impeller of the pump from blockage. She could be blocked by shards of glass, so there was a lock.
2. Check and clean the drain hose. Disconnect it from the housing and the sewer and flush it under the tap. Sewerage is cleaned by special means.
3. Reinstall or repair the module.
1. The nozzles of the sprayer are clogged.
2. The engine that rotates the rocker arms does not work.
1. Clean the nozzles under the tap with a toothpick.
2. Carry out engine diagnostics and repairs.
1. Blockage in the filling system.
2. Faulty level sensor.
What can be done:
1. Check the water supply and filler system for blockage. Clean hose, strainer and filler valve.
2. Inspect the pressure switch. If there is a problem, install a new part.
1. Problems with the pressure switch.
2. The inlet valve does not open.
3. The pressure switch does not work.
1. There was a blockage in the filters.
2. Sprayer does not work well.
3. Detergent is very foaming. The amount of foam exceeds the amount of water.
1. Inspection and cleaning of all filters in the Virpul dishwasher.
2. Check sprayer operation.
3. Use a new detergent or pour less.
Why does this happen:
1. Damaged inlet valve.
2. Problems with the operation of the electronic board. The failure of her triacs.
How to repair:
1. Inspection and diagnosis of the intake valve. Installing a new part.
2. Repair of triac control board.
1. Breakage of the indicator.
2. Clogged indicator lens.
3. Problems with the board or connections.
1. Replacing the OWI indicator in case of a problem.
2. Cleaning the lens from clogging.
3. Flashing the board or repairing wiring.
We introduced you to all the mistakes of the Whirlpool dishwashers. To carry out repairs yourself or not is up to you. We recommend that you conduct an independent inspection before calling the wizard to verify the cause of the failure.